Skip to Main Content
Edlx10 5gal

100% Acrylic Ultra-Premium flexible, long lasting elastomeric wall coating

ENDURALASTIC® 10 is an ultra-premium specialty 100% acrylic elastomeric wall coating designed for use on exterior surfaces. ENDURALASTIC 10 has exceptional flexibility, chalking and binder degradation resistance, and provides outstanding waterproofing protection against wind-driven rain by bridging hairline cracks. ENDURALASTIC 10 also provides excellent adhesion and outstanding alkali and efflorescence resistance on properly prepared masonry.

  • Superior elasticity and elongation
  • Excellent crack bridging properties
  • Waterproofs against wind-driven rain
  • Great dirt pick-up resistance
Applications Small edlx10 5gal
Flat
Brick
Concrete Block
Plaster
Poured-in-Place
Smooth Towel
Stucco
Tilt-Up Concrete

See the ENDURALASTIC™ difference.


Crack Bridging

Hairline cracks are unsightly surface defects that can be found on various exterior masonry surfaces. Enduralastic 10 is uniquely formulated flexible coating that seals and bridges hairline cracks, which provides excellent waterproofing protection against wind-driven rain.

CrackBridging CrackBridging CrackBridging CrackBridging

Crack Bridging Test Method: A stucco mixture is prepared using cement, sand, water and lime. The stucco mixture is applied evenly and no more than 1/4" thick over a panel. The prepared panel is allowed to dry for a week. After the panels are cured, the test paint is applied using a brush to the appropriate mil thickness and cured for a week. After a week, the panel is bent over a 5" diameter metal can. The panel is evaluated for any visible cracks on the film. If no cracks are visible then the can is bent over a 4" diameter can. Each portion of the panel is rated on a scale.


Chalking/Binder Degradation Resistance

Coatings that exhibit good resistance to weathering such as UV light (sunlight) and moisture will maintain their original appearance longer. Enduralastic 10 clearly beats the Regional and National Brands.

Degradation Degradation Degradation Degradation

Chalking/Binder Degradation Resistance Test Method: Exposure data is necessary for the selection of new materials and improvement of existing materials. The QUV machine reproduces the damaging effects of sunlight by using fluorescent UV lamps. It also uses a hot condensation mechanism that reproduces outdoor moisture similar to dew. The use of QUV machines allows the lab to monitor and evaluate product deterioration in a more controlled manner. Aluminum Q-panels are cleaned using acetone to remove any impurities. All panels are primed with Ultra-Grip Premium using an airless sprayer and allowed to dry overnight. The following day, each panel is coated using a 30 mil clearance square applicator. After seven day cure time, each panel is read for gloss, color readings, and photographed before exposure. The panels are mounted in snap-ring holders and placed into the QUV accelerated weathering machine. The QUV machine is programed to cycle between four hours of UV light, with irradience of 0.68, and four hours of condensation, 40° C. The panels are exposed to these conditions for a total of 1250 hours. Every 250 hours, each panel is evaluated for gloss retention, color retention, blistering, chalking/binder degradation, cracking/flaking and adhesion.

It is always recommended that ENDURALASTIC 10 be used over properly prepared and primed surfaces. Below are our best primers for use on each type of surface.

Masonry

Surface Recommended Primer
Plaster, Stucco (new), Stucco (repaint),
Tilt-up Concrete, Poured-in-place, Brick, Smooth Trowel
SUPER-LOC®
EFF-STOP® Select
ENDURASEAL® Exterior Masonry Sealer
FLEX-PRIME® Select
Concrete Block Smooth BLOCFIL Premium
Smooth BLOCFIL Select

Other Products